EnglishEspañolPortuguese
Innovations in Process Instrumentation & Control.
Company Certified ISO-9001:2008
Inquiry List

Water & Waste Water Treatment.

 

TPX-770-I

SUBMERSIBLE LEVEL TRANSMITTER

Ideal to measure in lakes, rivers or underground tanks.

Add this product to the Inquiry List.
Hydrostatic Level Transmitters
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
Instrument or equipment available with Environmental (Ingress) Protection IP-68 (Equivalent to NEMA-6P). Allows full inmersion for indefinite time.
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
 

G-SLT5.

ULTRASONIC LEVEL TRANSMITTER

Typical accuracy: 0.25% FS. Measurement ranges between 10 and 30 m.

The instrument has transmission (4...20 mA) and control (relay contacts) outputs.

Add this product to the Inquiry List.
UltraSonic & Radar Level Transmitters
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
The sensing device or active parts of this instrument have direct no contact with the process fluid.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

G-DLT2

ULTRASONIC DIFFERENTIAL LEVEL TRANSMITTER

Specially designed to monitor barscreens and similar devices.

It can measure and transmitt upstream level, downstream level or the difference between both.

Add this product to the Inquiry List.
UltraSonic & Radar Level Transmitters
The sensing device or active parts of this instrument have direct no contact with the process fluid.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
This instrument is available with auxiliary alarm and/or control outputs. Typically these are SPDT contacts, free of potential, that can be configured for High and/or Low conditions.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 
 

G-PSL0

eeee

Specially suited for the pumping of sewage or storm water.

 

M-4189

TILT FLOAT LEVEL SWITCH

Ideal and simple solution for open tanks, sumps and ponds.

Very strong construction in high quality polymers.

Add this product to the Inquiry List.
Level Switches
The primary unit (in other words, the part "wet" by the process fluids) of this instrument is available with construction in engineering plastics, such as:  PVC, CPVC, PP, PTFE, PVDF, PPS, etc.
Download the technical Data Sheet of this product.
 

EMG-L

ELECTROMAGNETIC FLOWMETER FOR LARGE PIPES

Available from 18" through 80". Ideal for drinking or waste water.

Add this product to the Inquiry List.
ElectroMagnetic Flowmeters
This instrument is suitable to measure river water, well water or other raw waters.
This instrument is suitable to measure all kind of waste water. Including raw or partially filtered sewage.
This flowmeter works based in an electromagnetic induction technology. It is only suitable to measure electric conductive liquids, typically liquids containing water. The minimum electric conductivity should be in the range of 5...20 uSiemens.
This flowmeter has no restriction to the fluid passage (Full bore section). It is therefore, a "zero" pressure drop instrument.
This electro-magnetic flowmeter can be supplied with electrodes made of special materials (such as, Hastelloy C, Titanium, Tantalum, etc) or with special functions (self cleaning design)
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

EMG-I

INSERTION ELECTROMAGNETIC FLOWMETER

Suitable for very large pipes. Diameter range: 4" through 160".

Optionally with "hot tap" mounting under line pressure.

Add this product to the Inquiry List.
ElectroMagnetic Flowmeters
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
This flowmeter works based in an electromagnetic induction technology. It is only suitable to measure electric conductive liquids, typically liquids containing water. The minimum electric conductivity should be in the range of 5...20 uSiemens.
Insertion instrument suitable to be mounted in the process piping (with no service interruptions) by Hot Tap procedures.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
 

TimeDelta

TRANSIT TIME ULTRASONIC FLOWMETER. (Non-Contact)

Suitable for pipes ranging from 1/2" to 240". Accuracy up to 1% of reading.

Optionally with double beam system.

Add this product to the Inquiry List.
Ultra-Sonic Flowmeters, Non-Contacting & In-Line
This instrument, equipment or option is among the most popular within its category.
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
This flow flowmeter is based in the Ultra-Sonic Transit Time (Time of Flight) principle. It is a high reliability technology. Suitable for relatively clean and low aereated liquids.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Instrument available with ModBus-RTU digital communication protocol over a RS-485 interface.
Download the general catalog of this product line.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

PortaFlow

PORTABLE ULTRASONIC TRANSIT TIME + DOPPLER EFFECT FLOWMETER

With Anti-Bubble Algorithm. Can plot the velocity profile inside the pipe.

Accuracy (always) 1%. With data logger an battery that lasts longer than 12 Hrs.

Add this product to the Inquiry List.
Portable Flowmeters
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
Ideal to measure dirty liquids or liquids with a high degree of aeration. This definition normally includes liquids with at least 75 ppm of solids or 75 ppm of gas bubbles. The minimum size of the solids or bubbles should be >= 100 uM.
This flow flowmeter is based in the Ultra-Sonic Transit Time (Time of Flight) principle. It is a high reliability technology. Suitable for relatively clean and low aereated liquids.
This flowmeter is based in a Doppler Effect Ultra-Sonic principle. Requires relatively dirty or aereated liquids. The particles or bubbles are the echo producers.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

SGN-P

PADDLE WHEEL FLOW SENSOR

Can measure liquid velocities between 0.1 and 6.0 m/sec. For pipes ranging from 1/2" to 36".

Made of plastic materials. Ideal solution for drinking water.

Add this product to the Inquiry List.
Turbine Flowmeters, In-Line & Insertion
This product has one of the lowest total purchase prices, when compared with others within its category.
The primary unit (in other words, the part "wet" by the process fluids) of this instrument is available with construction in engineering plastics, such as:  PVC, CPVC, PP, PTFE, PVDF, PPS, etc.
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

SGN-M

INDUSTRIAL PADDLE WHEEL FLOWMETER

Can measure liquid velocities from 0.1 to 6.0 m/sec. Metallic construction.

Suitable for pipes from 1 1/2" to 24". Optionally with "hot tap" mounting.

Add this product to the Inquiry List.
Turbine Flowmeters, In-Line & Insertion
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
Insertion instrument suitable to be mounted in the process piping (with no service interruptions) by Hot Tap procedures.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

Flomic-W

ULTRASONIC FLOWMETER FOR WATER DISTRIBUTION NETWORKS

Battery powered. Includes data-logger.

For pipes ranging from 1" to 8". Ideal for drinking water distribution.

Add this product to the Inquiry List.
Ultra-Sonic Flowmeters, Non-Contacting & In-Line
This product has one of the lowest total purchase prices, when compared with others within its category.
Instrument or equipment available with Environmental (Ingress) Protection IP-68 (Equivalent to NEMA-6P). Allows full inmersion for indefinite time.
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
This flowmeter has no restriction to the fluid passage (Full bore section). It is therefore, a "zero" pressure drop instrument.
This flow flowmeter is based in the Ultra-Sonic Transit Time (Time of Flight) principle. It is a high reliability technology. Suitable for relatively clean and low aereated liquids.
This instrument get its electric power from a Lithium battery. The battery's life span can typically go from 3 to 10 years. Optionally, It may also have an external power supply.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

Flomic-I

INSERTION ULTRASONIC FLOWMETER

Single or dual beam system. Special for large pipes: 8" to 80".

Add this product to the Inquiry List.
Ultra-Sonic Flowmeters, Non-Contacting & In-Line
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
This flow flowmeter is based in the Ultra-Sonic Transit Time (Time of Flight) principle. It is a high reliability technology. Suitable for relatively clean and low aereated liquids.
Insertion instrument suitable to be mounted in the process piping (with no service interruptions) by Hot Tap procedures.
Instrument with transmission (or re-transmission) ouput signal in the range of 4 .... 20 mADC.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

G-DFM5

DOPPLER EFFECT FLOW TRANSMITTER. (Non-Contact)

Suitable for pipes ranging from 1" to 180". Can measure waste water and raw sewage.

Accurate to 2% of reading.

Add this product to the Inquiry List.
Ultra-Sonic Flowmeters, Non-Contacting & In-Line
This product has one of the lowest total purchase prices, when compared with others within its category.
This instrument is suitable to measure all kind of waste water. Including raw or partially filtered sewage.
Ideal to measure dirty liquids or liquids with a high degree of aeration. This definition normally includes liquids with at least 75 ppm of solids or 75 ppm of gas bubbles. The minimum size of the solids or bubbles should be >= 100 uM.
This instrument is convenient, both from an economic and technical point of view, to measure in large pipes. Typically nominal sizes larger than 10". Consult the catalog or data-sheet in order to determine the maximum size available.
This flowmeter is based in a Doppler Effect Ultra-Sonic principle. Requires relatively dirty or aereated liquids. The particles or bubbles are the echo producers.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
This instrument is available with auxiliary alarm and/or control outputs. Typically these are SPDT contacts, free of potential, that can be configured for High and/or Low conditions.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

G-AVFM

AREA - VELOCITY FLOW TRANSMITTER

No weir or flume required. The sensor is placed on the channel floor.

Velocity range from 0.03 to 6 m/sec and water depth up to 4.5 m.

Add this product to the Inquiry List.
Open Channel Flowmeters
This flowmeter is based in a Doppler Effect Ultra-Sonic principle. Requires relatively dirty or aereated liquids. The particles or bubbles are the echo producers.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
This instrument is available with auxiliary alarm and/or control outputs. Typically these are SPDT contacts, free of potential, that can be configured for High and/or Low conditions.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

G-OCF5

ADVANCED OPEN CHANNEL FLOW TRANSMITTER. (Non-Contact)

Suitable for all weirs, flumes, "V" notchs, etc.

Includes data logger and alarm contacts.

Add this product to the Inquiry List.
Open Channel Flowmeters
This open channel flowmeter is suitable to work in conjuction with all kind of Weir (V Notch, Cipolletti, etc) or Flume (Parshall, Palmer-Bowlus, etc).
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Instrument available with integrated digital data logger. Typically the memory is non-volatile and the data is downloaded using a special software package through a USB, RS-232 or wireless infrared interface.
This instrument is available with auxiliary alarm and/or control outputs. Typically these are SPDT contacts, free of potential, that can be configured for High and/or Low conditions.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

LHI-xx

pH / ORP / DISSOLVED OXYGEN TRANSMITTER

With a galvanically isolated 4...20 mA output. Very simple calibration routine. With temperature compensation.

Special construction for corrosive and humid environments.

Add this product to the Inquiry List.
Electrochemical Instrumentation
This product has one of the lowest total purchase prices, when compared with others within its category.
Instrument or equipment available with Environmental (Ingress) Protection IP-65 or higher (Equivalent to NEMA-4X). This degree of protection is normally recommended for outdoor service.
This instrument is available with a combination of construction materials (for the primary and/or enclosure) that make it suitable for service or operation in environments with corrosive compundes, such as wet Cl2, HCl, NaOCl, etc.
This flowmeter may include an additional 4...20 mA output to be assigned as Temperature Transmitter.
This instrument has Galvanic Isolation (typically 1500 VAC) between the input and output circuits (or beteween the I/O circuits and the power supply, if the last is independent)
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Download the general catalog of this product line.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

M-12

SELFCLEANING pH SENSOR (3/4")

As above, but whit a flat-concave sensing surface that prevents sediment built-up.

Add this product to the Inquiry List.
Electrochemical Instrumentation
Instrument or equipment available with Environmental (Ingress) Protection IP-68 (Equivalent to NEMA-6P). Allows full inmersion for indefinite time.
This instrument is suitable to measure all kind of waste water. Including raw or partially filtered sewage.
Ideal to measure clean liquids with low degree of aeration. This definition typically involves liquids with Turbidity <= 10 g/l and Gas Concentrations <= 3% per volume. (Note: Gas in Liquid will generate a positive error in volumetric flowmeters).
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

Copyright &copy; 2012...2016 CONAR. Innovations in Process Instrumentation & Control.