EnglishEspañolPortuguese
Like !
Innovations in Process Instrumentation & Control.
Company Certified ISO-9001:2008

Home

Products and Services

Resources

News and Events

SiteInfo

Contact
Inquiry List
CheckOut

Sanitary and Asceptic Processes

 

TPX-770-S

Like !

SANITARY HYDROSTATIC LEVEL TRANSMITTER

With Tri-Clamp or Danish, SMS or DIN-11851 unions.

Special versions for high temperature.

Add this product to the Inquiry List.
Hydrostatic Level Transmitters
This instrument, equipment or option is among the most popular within its category.
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This transmitter is available with a wide variety of hydraulic filling fluids, such as: Silicon Oil, Fluorinated Oil (Fluorolube, for Oxygen, Cl2 or F2 service) and Food Grade Esters (Neobee, FDA approved).
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
 

TPX-770-E

Like !

HYDROSTATIC LEVEL TRANSMITTER FOR SANITARY / ASCEPTIC SERVICE.

Same as above, but with extended diaphragm to assure perfect flush mounting.

Add this product to the Inquiry List.
Hydrostatic Level Transmitters
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
Besides the classic enclosures made of Aluminum, this Instrument is available with the electronics enclosure made of special materials, such as: Stainless Steel, Sanitary Plastics (FDA approved) or other.
This transmitter is available with a wide variety of hydraulic filling fluids, such as: Silicon Oil, Fluorinated Oil (Fluorolube, for Oxygen, Cl2 or F2 service) and Food Grade Esters (Neobee, FDA approved).
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
 

TPX-770-SS

Like !

SANITARY INDUSTRIAL GAGE PRESSURE TRANSMITTER

Same as above but with sanitary connections. Available with Tri-Clover (ISO) Clamp, or Danish, SMS or DIN-11851 unions.

Add this product to the Inquiry List.
Gage & Absolute Pressure Transmitters
This instrument, equipment or option is among the most popular within its category.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This transmitter with flush diaphragm is ideal to handle sanitary, sticky, dirty or with possibility of polimerization fluids. It may also include an Diaprhagm Extension in order to minimize the deposition of foreign material in the process connection.
This transmitter is available with a wide variety of hydraulic filling fluids, such as: Silicon Oil, Fluorinated Oil (Fluorolube, for Oxygen, Cl2 or F2 service) and Food Grade Esters (Neobee, FDA approved).
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
 

LTS-1620-S

Like !

SANITARY SERVICE MAGNETIC LEVEL TRANSMITTER

With sanitary connections: Tri-Clamp or Unions Danish, SMS or DIN-11851.

Add this product to the Inquiry List.
Magnetic Level Transmitters
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is NOT affected by the density of the liquid being measured.
This level measurement instrument is NOT affected by foam build-up on the liquid surface.
The accuracy and reliability of this instrument is NOT affected by the composition, density or stratification of the gases or vapours above the liquid surface.
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
 

TEX-102-S

Like !

COMPACT SANITARY TEMPRATURE SENSOR

Integral style construction, does note require an additional thermowell.

With ISO Clamp (Tri-Clamp) connections or Danish, SMS or DIN-11851 sanitary unions.

Add this product to the Inquiry List.
Temperature Sensors + Thermowells
This instrument ranks at the top in Total Measurement Accuracy when compared to others within its category or with instruments of competitive technologies.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This sensor is available with compact construction (MgO) for vibration proof service.
Download the technical Data Sheet of this product.
 

TTX-380-S

Like !

SANITARY TEMPERATURE TRANSMITTER

Special design for sanitary applications.

With enclosures made of stainless steel or plastic (FDA approved) with integral cable glands.

Add this product to the Inquiry List.
Temperature Transmitters
This product is new and has been launched into the market or totally revamped less than one year ago.
Instrument or equipment available with Environmental (Ingress) Protection IP-65 or higher (Equivalent to NEMA-4X). This degree of protection is normally recommended for outdoor service.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This transmitter has a 4...20 mA (or 4...20 mA + HART) output over a two wire circuit, with a nominal power supply of 24 VDC. (Typically the voltage supply is allowed to swing between 12 and 36 VDC).
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
Download the technical Data Sheet of this product.
 

FloNet-S

Like !

SANITARY ELECTROMAGNETIC FLOWMETER

With ISO Clamp (Tri-Clover) or sanitary couplings. Between 1/2" and 4".

Minimum conductivity: 20 uS/cm. Up to 10 bar and 150 °C.

Add this product to the Inquiry List.
ElectroMagnetic Flowmeters
This product is new and has been launched into the market or totally revamped less than one year ago.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This flowmeter works based in an electromagnetic induction technology. It is only suitable to measure electric conductive liquids, typically liquids containing water. The minimum electric conductivity should be in the range of 5...20 uSiemens.
This flowmeter has no restriction to the fluid passage (Full bore section). It is therefore, a "zero" pressure drop instrument.
This electro-magnetic flowmeter can be supplied with electrodes made of special materials (such as, Hastelloy C, Titanium, Tantalum, etc) or with special functions (self cleaning design)
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

SP-S

Like !

SANITARY AXIAL TURBINE FLOWMETER

Available with Tri-Clamp connection between 1/2" and 4". Accuracy: 0.5% of reading.

Suitable for liquids and gases in the food and pharmaceutical industries.

Add this product to the Inquiry List.
Turbine Flowmeters, In-Line & Insertion
This instrument ranks at the top in Total Measurement Accuracy when compared to others within its category or with instruments of competitive technologies.
Certified by several Weights & Measures legal bodies with the purpose to be used in commercial transactions. (Custody transfer applications)
Certified by organizations such as 3A (USA), EHEDG (Europe) or equivalent in order to be used in sanitary or sterile processes.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

V-Mass

Like !

SEMI-STRAIGHT TUBE MASS FLOW TRANSMITTER

Five nominal sizes covering between 1/2" to 2".

Mass flow ranges from 60 kg/hr up to 96 ton/hr.

Add this product to the Inquiry List.
Coriolis Mass Flowmeters
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable to measure liquids (tipically with low viscosity) and all kind of gases.
Transmitter with independent circuits for the power supply (that typically can be 24 V, 110 V or 220 V) and the signal output, that normally is (0)4...20 mA, 0...5 VCD, 1...5VDC or 0...10 VDC.
Instrument available with HART digital communications protocol over the 4...20 output signal. HART is a very convenient tool for the instrument remote re-calibration, re-configuration or diagnostics.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download the technical Data Sheet of this product.
 

Eg-Delta-S

Like !

COMPACT VORTEX SANITARY FLOWMETER

Same as above but with sanitary connections.

Available with ISO (TriClover) Clamp or unions Danish, SMS or DIN.

Add this product to the Inquiry List.
Vortex & Target Flowmeters
This product has one of the lowest total purchase prices, when compared with others within its category.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable to measure low viscosity liquids (tipically with <= 10 cPoise) and all kind of gases.
This instrument get its electric power from a Lithium battery. The battery's life span can typically go from 3 to 10 years. Optionally, It may also have an external power supply.
Instrument with transmission (or re-transmission) ouput signal in the range of 4 .... 20 mADC.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the general catalog of this product line.
 

Eg-Pulse-S

Like !

LOW COST SANITARY VORTEX FLOW SENSOR

Same as above but with sanitary connections.

Available with ISO (TriClover) Clamp or with unions Danish, SMS or DIN.

Add this product to the Inquiry List.
Vortex & Target Flowmeters
This product has one of the lowest total purchase prices, when compared with others within its category.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is available with direct digital pulse output. These puses typically can be used for volume or mass totalization.
Download the general catalog of this product line.
Download the technical Data Sheet of this product.
Download an Instruction Manual (Installation anr/or operation and/or maintenance) of this product.
 

MG-562-S

Like !

LOOP POWERED FIELD DIGITAL INDICATOR. STAINLESS STEEL ENCLOSURE.

Back lit LCD with four digit capacity. Powered by the current loop (4...20 mA).

With engineering unit indication and addtional bar-graph. Stainless steel enclosure with optional integral cable glands.

Add this product to the Inquiry List.
Field Digital Indicators
This product is new and has been launched into the market or totally revamped less than one year ago.
This instrument, equipment or option is among the most popular within its category.
Instrument available with Flameproof (Explosionproof) Certification. Depending on the circumstances, this certification could be Ex d IIB+H2 T6 (ATEX, INTI, or equivalent) and/or Class II, III; Div 1; Gropus B, C, D, E, F,G (FM, CSA or equivalent)
This instrument is avaiblable with Intrinsic Safety Certification. Depending on the specific cases it could be Ex ia IIB+H2 T6 (ATEX, INTI or equivalent) and/or Class I, II, III; Div 1; Groups B, C, D, E, F, G (FM, CSA or equivalent)
Besides the classic enclosures made of Aluminum, this Instrument is available with the electronics enclosure made of special materials, such as: Stainless Steel, Sanitary Plastics (FDA approved) or other.
This instrument is HART transparent. This means that it can be inserted in a measurement loop without affecting the functionality or reliability of the HART communications.
Download the technical Data Sheet of this product.
 

i-LED-CD

Like !

PROCESS ILLUMINATOR WITH INTEGRAL SANITARY OBSEVATION WINDOW

"All in one" complete assembbly: sanitary observation window + solid state crown illuminator.

For sanitary connections sized 6", 5" and 4". For ISO Clamps (Tri-Clamp) or unions SMS, DIN-11851 or Danish.

Add this product to the Inquiry List.
Process Observation. Illuminators & Sight Windows
Instrument or equipment available with Environmental (Ingress) Protection IP-65 or higher (Equivalent to NEMA-4X). This degree of protection is normally recommended for outdoor service.
Instrument available with Sanitary Process Connections. Depending on the requirements these connections could be: a) ISO-2852 (TriClover, 3A) Clamp, b) Danish Union according to DS-722, c) Swedish Union as per SMS-1145, or d) DIN Union as per DIN-11851.
Suitable for sanitary Clean in Place processes. This typically means service at T >= 80 °C and with fluids such as lean solutions of NaOH, HNO3, detergents and similar.
This instrument is suitable for sterile sanitary processes with "Sterilize in Place" procedures. This typically means service at T >= 120 °C for a minimum time of 30 minutes and in direct contact with steam or other chemicals.
Download the technical Data Sheet of this product.
 

Copyright &copy; 2012...2016 CONAR. Innovations in Process Instrumentation & Control.